| |
 |
|
|
Rock-AssaultTM
Ram Steering
The Rock-AssaultTM
Ram Steering assist kit is the best kit you
will find anywhere! Our Toyota kit features
a 6" X 1.5" stroke hydraulic ram with high
temp inner and outer seals for long life and
no leaks. Our specially designed ram
features a 3/4" rod that is 50% stronger
than other 1/2" rods on the market. For Dana
knuckle applications we also offer an 8"
stroke version.
Our specially
formed, easy to install brackets make
installing our kit a breeze. If you have
looked at other kits on the market, you will
see they either don't include mounts or they
just provide generic tabs. Our mounting
hardware is specially designed to fit the
Toyota axle and High Steer. Once the
steering box has been tapped, installation
of the ram takes about one hour. Each
bracket is formed from heavy-duty 1/4" plate
steel for extra strength. Fits 1979 - 1995
Toyota Pickup and 4Runner with solid front
axle.
Included with
each ram kit:
- Ram with
high temp inner and outer seals
- Rod
ends w/jam nut
- Ram
bracket for axle housing
- Ram
bracket for tie rod
- (2)
Hoses
- (2) JIC
90 degree elbows
- Mounting
Hardware
-
Instructions w/photos
Kit requires:
-
High
Steer crossover steering with 1.25" tie rod
- Tapped
steering box
 |
Rock Assault
Ram Steering Kit,
1.5" X 6", $199, 130250-1-K |
|
|
Rock Assault
Ram Steering Kit, 2" X 6", $219, 130265-1-K |
|
|
Rock Assault
Ram Steering Kit, 2" X 8", $219, 130266-1-K |
Application
Notes:
If you
purchase a tapped steering box from
Trail-Gear, the box will include two, 1/4"
pipe to JIC fittings on the box. If you will
be tapping your own steering box, you will
need to purchase a pair of 1/4" to JIC #6
fittings for the steering box. The
Trail-Gear part number for this fitting is
130263-1 and they can be purchased
here.
Adding a ram
assist steering to a truck with the stock
power steering pump will slow the steering
noticeably. While it will take less steering
wheel effort to turn the wheels, but it will
take a little longer time to to turn the
wheels, especially at low engine rpm's. The
larger the ram bore then more noticeable the
slowness becomes. If you are planning to use
the stock Toyota power steering pump we
recommend using the 1.5" ram. We strongly
recommend using a high volume/pressure "TC"
style pump when using 2" bore rams. On
V6 applications, the oil pan may need to be
modified or replaced to make room for the
ram.
|
|
|
Power Steering Pump without Pulley
This TC style power steering
pump is the best of the best.
It features an all steel housing
to handle extreme heat and puts
out an amazing 4.5 GPM of flow
and 1,650PSI of pressure. Pump
has #6 JIC male on pressure port
and #10 JIC fitting on suction
side. Each pump is bench tested
to ensure quality. This pump
will run all full hydraulic
applications popularly used in
rock crawling today.
Pulley not included.
Note:
Using
anything other than a power
steering pulley installer to
install your pulley on this pump
will void the warranty.
Never use ATF fluid, or a
semi-synthetic blend. This will void the
warranty.
Ok to use
standard power steering fluid or a full
synthetic.
Royal Purple fully synthetic power steering
fluid recommended.
|
|
Power Steering
Pump without Pulley, $175, 130303 |
|
|
|
Power Steering Pump with Pulley
This TC style power steering pump is
the best of the best. It features
an all steel housing to handle
extreme heat and puts out an
amazing 4.5 GPM of flow and 1,650PSI
of pressure. The anodized aluminum
pulley on this pump is designed to
fit Toyota applications and is
shipped pre-installed. Each pump is
bench tested to ensure quality.
This pump will run all full
hydraulic applications popularly
used in rock crawling today.
Note: Never use ATF fluid, or a
semi-synthetic blend. This will void the
warranty.
Ok to use
standard power steering fluid or a full
synthetic.
Royal Purple fully synthetic power steering
fluid recommended.
|
|
Power Steering
Pump with Pulley, $175, 130304-1-K |
|
|
|
Replacement Parts
|
|
Hydraulic Hose,
50" Long,
Ram Steering, $15, 130255-1 |
|
|
Elbow Fitting,
#6 JIC, $7, 130256-1 |
|
 |
|
1.5" Hydro Rams
& Connecting Parts
Hydraulic ram with high
temp inner and outer seals for long life and
no leaks. Our specially designed ram
features a 3/4" rod that is 50% stronger
then other 1/2" rods on the market. Ram
requires rod ends, sold separately. Six inch
application for Toyota knuckles. Eight inch
application for Dana style steering knuckles.
Mounting brackets shown are designed to fit
Toyota solid axle front housing and 1.25"
tie rod.
|
|
Hydro ram 1.5" X
6",
$140 each, 130250-1 |
|
|
Rod End, 5/8",
Male,
$16 each, 130252-1 |
|
|
Jam Nut, 5/8" ,
$2 each, 130257-1 |
|
|
Rod End, 5/8",
Female,
$16 each, 130251-1 |
|
|
Hydro Bracket,
1.5" Ram,
Axle Housing, $15 each, 130254-1 |
|
|
Hydro Bracket,
1.5" Ram, Tie Rod, $15 each, 130253-1 |
|
|
Hydro Bracket
Spacer, 1.5" Ram, $1 each, 130262-1 |
|
 |
|
2" Hydro Rams & Connecting Parts
Same
as above but with larger 2" piston and .800
shaft.
|
|
Hydro ram 2" X
6", $160 each, 130265-1 |
|
|
Hydro ram 2" X
8", $160 each, 130266-1 |
|
|
Rod End, 3/4",
Male, $16 each, 130268-1 |
|
|
Rod End, 3/4",
Female, $16 each, 130267-1 |
|
|
Jam Nut, 3/4",
$2 each, 130269-1 |
|
|
Hydro Bracket,
2" Ram, Axle Housing, $15 each, 130276-1 |
|
|
Hydro Bracket,
2" Ram, Tie Rod, $15 each, 130275-1 |
|
|
Hydro Bracket
Spacer, 2" Ram, $1 each, 130274-1 |
|
 |
|
|
Related Products:
|
|
|
|
